The insulator-to-metal transition in Mott insulators is the key mechanism for most of the electronic devices belonging to the Mottronics family. Intense research efforts are currently devoted to the development of specific control protocols, usually based on the application of voltage, strain, pressure, and light excitation. The ultimate goal is to achieve the complete control of the electronic phase transformation, with dramatic impact on the performance, for example, of resistive-switching devices. Here, we investigate the simultaneous effect of external voltage and excitation by ultrashort light pulses on a single Mottronic device based on a ${\mathrm{V}}_2{\mathrm{O}}_3$ epitaxial thin film. The experiments are supported by both finite-element simulations of the thermal problem and a simpler lumped-element model. The thermal models are benchmarked against results obtained at very low applied voltage ($\mathrm{\Delta }V=5$ mV). When the voltage is significantly increased ($\mathrm{\Delta }V=0.5$ V), but still in the linear below-switching-threshold region, our results show that the light excitation drives a volatile resistivity drop, which goes beyond the combined effect of laser and Joule heating. Our results impact on the development of protocols for the nonthermal control of the resistive-switching transition in correlated materials.

Terahertz (THz) emission from a $\mathrm{Fe}(211)/\mathrm{Pt}(110)$ bilayer grown on $\mathrm{Mg}\mathrm{O}(110)$ is systematically investigated. The intensity of the emitted THz wave strongly depends on the magnetization (M) orientation, and the measured THz field is 11% larger for M||$\mathrm{Pt}[1\overline{1}0]$ than for M||Pt[001]. Using first-principles calculations combined with the superdiffusive spin-transport model, we reveal that the lattice distortion induced by epitaxial strain causes anisotropic behavior of the electronic conductance and spin Hall conductivity, which eventually lead to the aforementioned experimental observations. Our studies thus provide a route to modify THz emission utilizing the intrinsic crystal-structure degree of freedom.

Copper-indium-gallium-selenide (CIGS) alloys are successfully applied in thin-film solar cells. For a better use of the solar spectrum, they also offer the possibility of multijunction devices by tuning the composition in the different layers. As-grown CIGS is intrinsically p-type due to copper vacancies ($V_{\mathrm{Cu}}$), but n-type doping is also useful for applications. While ${\mathrm{Cu}\mathrm{In}\mathrm{Se}}_2$ can be easily turned n-type, ${\mathrm{Cu}\mathrm{Ga}\mathrm{Se}}_2$ cannot, and this represents a problem, because increasing the band gap of CIGS requires a high $\mathrm{Ga}/\mathrm{In}$ ratio. Investigating the effect of hydrogen on ${\mathrm{Cu}\mathrm{Ga}\mathrm{Se}}_2$ by an optimized hybrid functional, we show that hydrogenation from an atomic source as, e.g., by a hydrogen plasma treatment, can turn the material n-type due to the formation of shallow donor $V_{\mathrm{Cu}}+2\mathrm{H}$ complexes, while ${\mathrm{H}}_2$ implantation, producing an internal hydrogen reservoir, can be used to produce semi-insulating material. We also show that under normal process conditions, unintentional hydrogen incorporation does not have a significant effect on ${\mathrm{Cu}\mathrm{Ga}\mathrm{Se}}_2$.

We introduce a double quantum (DQ) 4-Ramsey measurement protocol that enables wide-field magnetic imaging using nitrogen-vacancy ($\mathrm{N}$-$V$) centers in diamond, with enhanced homogeneity of the magnetic sensitivity relative to conventional single quantum (SQ) techniques. The DQ 4-Ramsey protocol employs microwave-phase alternation across four consecutive Ramsey (4-Ramsey) measurements to isolate the desired DQ magnetic signal from any residual SQ signal induced by microwave pulse errors. In a demonstration experiment employing a 1-$\mu \mathrm{m}$-thick $\mathrm{N}$-$V$ layer in a macroscopic diamond chip, the DQ 4-Ramsey protocol provides a volume-normalized dc magnetic sensitivity of ${\eta }^V=34\mathrm{nT}{\mathrm{Hz}}^{-1/2}\mu {\mathrm{m}}^{3/2}$ across a $125\mu \mathrm{m}\times 125\mu \mathrm{m}$ field of view, with about $5\times$ less spatial variation in sensitivity across the field of view compared to a SQ measurement. The improved robustness and magnetic sensitivity homogeneity of the DQ 4-Ramsey protocol enables imaging of dynamic broadband magnetic sources such as integrated circuits and electrically active cells.

Recent advances in optical beam shaping have enabled a wide class of structured lights that follow exotic trajectories, opening many routes for numerous applications. Although the Helmholtz equation sets stringent conditions on the fields that can be physically realized, these constraints can be removed if sources can be introduced inside the medium. However, introducing sources is not always possible or practical. Here, we propose an analytical approach that transforms the effects of the required sources from the inside of the medium to its boundaries. The derived boundary conditions can then be used to generate any desired optical field (amplitude and phase). We demonstrate the feasibility of the approach by experimentally generating two optical fields inside a source-free simple medium, demonstrating control over the trajectories, phases, and intensities of the fields.

Strong coupling of electromagnetic cavity fields with antiferromagnetic spin waves in hematite ($\alpha$-${\mathrm{Fe}}_2{\mathrm{O}}_3$) is achieved above room temperature. A cube of hematite is placed in a metallic tube and the transmission is measured, using a continuous-wave terahertz spectrometer. The spectra, collected as a function of the temperature, reveal the formation of magnetic polaritons.

Quantum key distribution (QKD) allows the establishment of common cryptographic keys among distant parties. Many of the QKD protocols that were introduced in the past, involve the challenge of monitoring the signal disturbance over the communication line, in order to evaluate the information leakage to a potential eavesdropper. Recently, a QKD protocol that circumvents the need for monitoring signal disturbance, has been proposed and demonstrated in initial experiments. Here, we propose an improved version of this so-called round-robin differential phase-shifting (RRDPS) protocol, in which both time and phase degrees of freedom are utilized to enlarge the Hilbert-space dimensionality, without increasing experimental complexity or relaxing security assumptions. We derive the security proofs of the round-robin differential phase-time-shifting (RRDPTS) protocol in the collective attack scenario, and benchmark it against RRDPS for different experimental parameters. Furthermore, a proof-of-concept experiment of the RRDPTS protocol, using weak coherent pulses and decoy state method, is demonstrated over 80 km of fiber link. Our results show that the RRDPTS protocol can achieve higher secret key rate in comparison with the RRDPS, in the condition of high quantum bit error rate.

Experiments involving optical traps often require careful control of the ac Stark shifts induced by strong confining light fields. By carefully balancing light shifts between two atomic states of interest, optical traps at the magic wavelength have been especially effective at suppressing deleterious effects stemming from such shifts. Highlighting the power of this technique, optical clocks today exploit Lamb-Dicke confinement in magic-wavelength optical traps, in some cases realizing shift cancelation at the ten parts per billion level. Theory and empirical measurements can be used at varying levels of precision to determine the magic wavelength where shift cancelation occurs. However, lasers exhibit background spectra from amplified spontaneous emission or other lasing modes that can easily contaminate measurement of the magic wavelength and its reproducibility in other experiments or conditions. Indeed, residual light shifts from laser background have plagued optical lattice clock measurements for years. In this work, we develop a simple theoretical model allowing prediction of light shifts from measured background spectra. We demonstrate good agreement between this model and measurements of the background light shift from an amplified diode laser in a Yb optical lattice clock. Additionally, we model and experimentally characterize the filtering effect of a volume Bragg grating bandpass filter, demonstrating that application of the filter can reduce background light shifts from amplified spontaneous emission well below the ${10}^{-18}$ fractional clock frequency level. This demonstration is corroborated by direct clock comparisons between a filtered amplified diode laser and a filtered titanium:sapphire laser.

We present a polarization-insensitive metasurface processor to perform spatial asymmetric filtering of an incident beam, thereby allowing for real-time parallel analog processing. To enable massive parallel processing, we introduce a multiple-input multiple-output (MIMO) computational metasurface with asymmetric response that can perform spatial differentiation on two distinct input signals regardless of their polarization. In our scenario, two distinct signals set in $x$ and $y$ directions, parallel and perpendicular to the incident plane, illuminate simultaneously the metasurface processor, and the resulting differentiated signals are separated from each other via appropriate spatial low-pass filters. By leveraging generalized sheet transition conditions and surface susceptibility tensors, we design an asymmetric meta-atom augmented with normal susceptibilities to reach asymmetric response at normal beam illumination. Proof-of-principle simulations are also reported along with the successful realization of signal processing functions. The proposed metasurface overcomes major shortcomings imposed by previous studies, such as large architectures arising from the need for additional subblocks, slow responses, and, most importantly, supporting only a single input with a given polarization. Our results set the path for future developments of material-based analog computing using efficient and easy-to-fabricate MIMO processors for compact, fast, and integrable computing elements without any Fourier lens.

Electrodes in close proximity to an active area of a device are required for sufficient electrical control. The integration of such electrodes into optical devices can be challenging since low optical losses must be retained to realize high-quality operation. Here, we demonstrate that it is possible to place a metallic shallow phosphorus doped layer in a silicon microring cavity that can function at cryogenic temperatures. We verify that the shallow doping layer affects the local refractive index while inducing minimal losses with quality factors up to ${10}^5$. This demonstration opens up a pathway to the integration of an electronic device, such as a single-electron transistor, into an optical circuit on the same material platform.

We study the interplay between quantum annealing parameters in embedded problems, providing both deeper insights into the physics of these devices and pragmatic recommendations to improve performance on optimization problems. We choose as our test case the class of bounded-degree minimum-spanning-tree problems. Through runs on a D-Wave quantum annealer, we demonstrate that pausing in a specific time window in the anneal provides improvement in the probability of success and in the time to solution for these problems. The time window is consistent across problem instances and its location is within the region suggested by prior theory and seen in previous results on native problems. An approach to enable gauge transformations for problems with the qubit coupling strength $J$ in an asymmetric range is presented and shown to significantly improve performance. We also confirm that the optimal pause location exhibits a shift with the magnitude of the ferromagnetic coupling, $|J_F|$, between physical qubits representing the same logical one. We extend the theoretical picture for pausing and thermalization in quantum annealing to the embedded case. This picture, along with perturbation-theory analysis and exact numerical results on small problems, confirms that the effective pause region moves earlier in the anneal as $|J_F|$ increases. It also suggests why pausing, while still providing significant benefit, has a less pronounced effect on embedded problems.

Excitation with entangled photon pairs may lead to an increase in the efficiency of two-photon absorption at low photon flux. The corresponding process, entangled two-photon absorption (E2PA), has been investigated in numerous theoretical and experimental studies. However, significant ambiguity and inconsistency remain in the literature about the absolute values of E2PA cross sections. Here, we use a fluorescence-based registration scheme to experimentally determine upper bounds on the cross sections for six fluorophores. These bounds are up to 4 orders of magnitude lower than the smallest published cross section. For two samples that have been studied by others, Rhodamine 6G and 9R-S, we measure upper bounds 4 and 5 orders of magnitude lower than the previously reported cross sections.

Quenching of limit-cycle oscillations (LCOs), either through mutual coupling or external forcing, has attracted wide attention in several fields of science and engineering. However, the simultaneous utilization of these coupling schemes in quenching of LCOs has rarely been studied despite its practical applicability. We study the dynamics of two thermoacoustic oscillators simultaneously subjected to mutual coupling and asymmetric external forcing through experiments and theoretical modeling. We investigate the forced response of both identical and nonidentical thermoacoustic oscillators for two different amplitudes of LCOs. Under mutual coupling alone, identical thermoacoustic oscillators display the occurrence of partial amplitude death and amplitude death, whereas under forcing alone, asynchronous quenching of LCOs is observed at nonresonant conditions. When the oscillators are simultaneously subjected to mutual coupling and asymmetric forcing, we observe a larger parametric region of oscillation quenching than when the two mechanisms are utilized individually. This enhancement in the region of oscillation quenching is due to the complementary effect of amplitude death and asynchronous quenching. However, the forced response of coupled nonidentical oscillators shows that the effect of forcing is insignificant on attaining synchronization and quenching of oscillations in the oscillator that is not directly forced. Finally, we qualitatively capture the experimental results using a reduced-order theoretical model of two Rijke tubes that are coupled through dissipative and time-delay coupling and asymmetrically forced. We believe that these findings offer fresh insights into the combined effects of mutual and forced synchronization in a system of coupled nonlinear oscillators.

Ferromagnet (FM)℃heavy-metal (HM) nanostructures can be used for magnetic state readout in the proposed magnetoelectric spin-orbit logic by locally injecting a spin-polarized current and measuring the spin-to-charge conversion via the spin Hall effect. However, this local configuration is prone to spurious signals. Here, we address spurious Hall effects that can contaminate the spin Hall signal in these FM/HM T-shaped nanostructures. The most pronounced Hall effects in our ${\mathrm{Co}}_{50}{\mathrm{Fe}}_{50}/\mathrm{Pt}$ nanostructures are the planar Hall effect and the anomalous Hall effect generated in the ferromagnetic nanowire. We find that the planar Hall effect, induced by misalignment between magnetization and current direction in the ferromagnetic wire, is manifested as a shift in the measured baseline resistance, but does not alter the spin Hall signal. In contrast, the anomalous Hall effect, arising from the charge-current distribution within the FM, adds to the spin Hall signal. However, the effect can be made insignificant by minimizing the shunting effect via proper design of the device. We conclude that local spin injection in FM/HM nanostructures is a suitable tool for measuring spin Hall signals and, therefore, a valid method for magnetic state readout in prospective spin-based logic.

We introduce the cavity-embedded Cooper-pair transistor (cCPT), a device that behaves as a highly nonlinear microwave cavity whose resonant frequency can be tuned both by charging a gate capacitor and by threading flux through a superconducting loop. We characterize this device and find excellent agreement between theory and experiment. A key difficulty in this characterization is the presence of frequency fluctuations comparable in scale to the cavity linewidth, which deform our measured resonance circles in accordance with recent theoretical predictions [Brock et al., Phys. Rev. Appl. 14, 054026 (2020)]. By measuring the power spectral density of these frequency fluctuations at carefully chosen points in parameter space, we find that they are primarily a result of the $1/f$ charge and flux noise common in solid-state devices. Notably, we also observe key signatures of frequency fluctuations induced by quantum fluctuations in the cavity field via the Kerr nonlinearity.

Van der Waals magnets are uniquely positioned at the intersection between two-dimensional materials, antiferromagnetic spintronics, and magnonics. The interlayer exchange interaction in these materials enables antiferromagnetic resonances to be accessed at gigahertz frequencies. Consequently, these layered antiferromagnets are intriguing materials out of which quantum hybrid magnonic devices can be fashioned. Here, we use both a modified macrospin model and micromagnetic simulations to demonstrate a comprehensive antiferromagnetic resonance spectra in van der Waals magnets near the ultrathin (monolayer) limit. The number of optical and acoustic magnon modes, as well as the mode frequencies, are found to be exquisitely sensitive to the number of layers. We discover a self-hybridization effect where pairs of either optical or acoustic magnons are found to interact and self-hybridize through the dynamic exchange interaction. This leads to characteristic avoided energy level crossings in the energy spectra. Through simulations, we show that, by electrically controlling the damping of surface layers within heterostructures, both the strength and number of avoided energy level crossings in the magnon spectra can be controlled.

In-plane uniformity of narrow-gap semiconductor $\mathrm{In}\mathrm{As}$/$\mathrm{Ga}\mathrm{Sb}$ type-II superlattice (T2SL) wafer is a crucial yet hard-to-evaluate prerequisite for high-performance long-wavelength infrared optoelectronic device applications of, e.g., focal-plane-array (FPA) photodetectors. In this work, we report a modulated photoluminescence-mapping (PL-mapping) study of $\mathrm{In}\mathrm{As}$/$\mathrm{Ga}\mathrm{Sb}$ T2SL in long-wavelength infrared range with a spatial resolution of a typical FPA-pixel scale. Spatial distributions are analyzed of PL-peak energy, linewidth, and integral intensity, which indicate a high in-plane uniformity of effective band gap but a considerable fluctuation of radiative recombination. The in-plane distributions of effective carrier lifetime and Shockley-Read-Hall defect concentration are evaluated, with the aid of a model that takes into account the pumping power dependence of the PL integral intensity. The results reveal a considerable in-plane nonuniformity of the optoelectronic response that may restrict the performance of the derivative FPA photodetector, and indicate the modulated PL mapping of a good pathway particularly for uniformity analysis of long-wavelength infrared FPA semiconductors.

Feedback amplification is a key technique for synthesizing various functionalities, especially in electronic circuits involving op amps. This paper presents a quantum version of this methodology, where the general phase-preserving quantum amplifier and coherent (i.e., measurement-free) feedback are employed to construct various types of systems having useful functionalities: quantum versions of differentiator, integrator, self-oscillator, and active filters. The class of active filters includes the Butterworth filter, which can be used to enhance the capacity of an optical quantum communication channel, and the nonreciprocal amplifier, which enables measurement of a superconducting qubits system as well as protection of it by separating input from output fields. A particularly detailed investigation is performed on the active phase-canceling filter for realizing a broadband gravitational-wave detector; that is, the feedback-amplification method is used to construct an active filter that compensates the phase delay of the signal and eventually recovers the sensitivity in the high-frequency regime.

Efforts by numerous research groups have provided a deeper insight into the physical mechanisms behind the power absorption of single-domain magnetic nanoparticles in magnetic-fluid-hyperthermia applications and theoretical models now account for the main experimental observations. However, the role of all parameters relevant to the magnetic relaxation remains a matter of debate. Here, we employ a nonlinear model for the magnetic relaxation of single-domain magnetic nanoparticles with uniaxial effective anisotropy and evaluate the influence of particle-intrinsic parameters as well as experimental conditions on the power absorption of both noninteracting and interacting systems (linear arrangements). These effects are assessed through the enclosed hysteresis area of the magnetization loops as a function of relative anisotropy $h_K$ (the anisotropy field with respect to the amplitude of the ac field), i.e., the “area curve” of the system. These curves can be divided into four regions with distinct magnetic responses and boundaries that depend on the particle size, frequency of the applied field and interactions. Interactions change the effective anisotropy of the system and shift the area curve towards lower $h_K$ values. For the low relative anisotropy range, dipolar interactions increase the area of the hysteresis loops [thus, the specific power absorption (SPA)], while they are detrimental or produce nonsignificant effects for the range of high relative anisotropy. Our study resolves seemingly contradictory results of interaction effects in linear arrangements recently reported in the literature. Simulations of randomly oriented particles and chains were contrasted with the oriented cases. An analytical approach and the thermal interpretation of its validity range are discussed, both aimed at the design of nanoparticles and the choice of the experimental conditions for optimal heating. We find that systems with low-thermal-fluctuation influence are better candidates for the application due to their high SPA values.