The photocathode rf gun is one of the most critical components in x-ray free electron lasers. The drive laser strikes the photocathode surface, which emits electrons with properties that depend on the shape of the drive laser. Most free electron lasers use photocathodes with work function in the ultraviolet, a wavelength where direct laser manipulation becomes challenging. In this paper, we present a novel application of a digital micromirror device (DMD) for the 253 nm drive laser at the Linear Coherent Light Source. Laser profile shaping is accomplished through an iterative algorithm that takes into account shaping error and efficiency. Next, we use laser shaping to control the X-ray laser output via an online optimizer, which shows improvement in FEL pulse energy. Lastly, as a preparation for electron beam shaping, we use the DMD to measure the photocathode quantum efficiency across cathode surface with an averaged laser rms spot size of $59\mu \mathrm{m}$. Our experiments demonstrate promising outlook of using DMD to shape ultraviolet lasers for photocathode rf guns with various applications.

Strong-field few-cycle terahertz (THz) pulses are an invaluable tool for engineering highly nonequilibrium states of matter. A scheme is proposed to generate quasi-half-cycle GV/m-scale THz pulses with a multikilohertz repetition rate. It makes use of coherent spontaneous emission from a prebunched electron beam traversing an optimally tapered undulator. The scheme is the further development of the slippage control in free-electron lasers [T. Tanaka, Phys. Rev. Lett. 114, 044801 (2015)]. An explicit condition for the spectral amplitude of undulator radiation and a phase condition for the electron density distribution, required for the generation of desired pulses, are presented. The amplitude condition is met by proper undulator tapering, and a generic optimal undulator profile is found analytically. In order to meet the phase condition, the distance between the adjacent bunches is varied according to the instantaneous resonant undulator wavelength. A 3D analytical theory is complemented by a detailed numerical study based on a direct solution to the 3D wave equation.

The recently proposed superconducting quadrupole resonator for Landau damping in accelerators is subjected to a detailed design study. The optimization process of two different cavity types is presented following the requirements of the High Luminosity Large Hadron Collider (HL-LHC) with the main focus on quadrupolar strength, surface peak fields, and impedance. The lower order and higher order mode (LOM and HOM) spectrum of the optimized cavities is investigated and different approaches for their damping are proposed. On the basis of an example the first two higher order multipole errors are calculated. Likewise on this example the required rf power and optimal external quality factor for the input coupler is derived.

A low-emittance thermionic-gun-based injector was developed for the x-ray free-electron laser (XFEL) facility known as the SPring-8 angstrom compact free-electron laser (SACLA). The thermionic-gun-based system has the advantages of maintainability, reliability, and stability over a photocathode radio-frequency (rf) gun because of its robust thermionic cathode. The basic performance of the injector prototype was confirmed at the SPring-8 compact self-amplified spontaneous emission source (SCSS) test accelerator, where stable FEL generation in an extreme ultraviolet wavelength range was demonstrated. The essential XFEL innovation is the achievement of a constant beam peak current of 3–4 kA, which is 10 times higher than that generated by the SCSS test accelerator, while maintaining a normalized-slice emittance below 1 mm mrad. Thus, the following five modifications were applied to the SACLA injector: (i) a nonlinear energy chirp correction; (ii) the optimization of the rf acceleration frequency; (iii) rf system stabilization; (iv) nondestructive beam monitoring; and (v) a geomagnetic field correction. The SACLA injector successfully achieved the target beam performance, which shows that a thermionic-gun-based injector is applicable to an XFEL accelerator system. This paper gives an overview of the SACLA injector and describes the physical and technical details, together with the electron beam performance obtained in the beam commissioning.

During Long Shutdown 1, 18 Large Hadron Collider (LHC) collimators were replaced with a new design, in which beam position monitor (BPM) pick-up buttons are embedded in the collimator jaws. The BPMs provide a direct measurement of the beam orbit at the collimators, and therefore can be used to align the collimators more quickly than using the standard technique which relies on feedback from beam losses. Online orbit measurements also allow for reducing operational margins in the collimation hierarchy placed specifically to cater for unknown orbit drifts, therefore decreasing the ${\beta }^{*}$ and increasing the luminosity reach of the LHC. In this paper, the results from the commissioning of the embedded BPMs in the LHC are presented. The data acquisition and control software architectures are reviewed. A comparison with the standard alignment technique is provided, together with a fill-to-fill analysis of the measured orbit in different machine modes, which will also be used to determine suitable beam interlocks for a tighter collimation hierarchy.

Fully stripped carbon ions generated in a laser-ablation ion source are directly injected into a small-scale induction synchrotron. Carbon-ion beams of ${\mathrm{C}}^{6+}$, ${\mathrm{C}}^{5+}$, and ${\mathrm{C}}^{4+}$ are trapped in the barrier bucket. Beam properties, such as the momentum spread and beam lifetime in the low-energy ring, are measured and discussed in relation to the essential characteristics required in a carbon driver for future carbon therapies.

In the framework of the program on medical applications a compact 750 MHz RFQ has been designed and built to be used as an injector for a hadron therapy linac. This RFQ was designed to accelerate protons to an energy of 5 MeV within only 2 m length. It is divided into four segments and equipped with 32 tuners in total. The length of the RFQ corresponds to $5\lambda$ which is considered to be close to the limit for field adjustment using only piston tuners. Moreover the high frequency, which is about double the frequency of existing RFQs, results in a sensitive structure and requires careful tuning. In this paper we present the tuning algorithm, the tuning procedure and rf measurements of the RFQ.

The conceptual design of the Future Circular Collider (FCC) is being carried out actively in an international collaboration hosted by CERN, for the post–Large Hadron Collider (LHC) era. The target center-of-mass energy of proton-proton collisions for the FCC is 100 TeV, nearly an order of magnitude higher than for LHC. The existing CERN accelerators will be used to prepare the beams for FCC. Concerning beam-related machine protection of the whole accelerator chain, it is critical to assess the consequences of beam impact on various accelerator components in the cases of controlled and uncontrolled beam losses. In this paper, we study the energy deposition of protons in solid copper and graphite targets, since the two materials are widely used in magnets, beam screens, collimators, and beam absorbers. Nominal injection and extraction energies in the hadron accelerator complex at CERN were selected in the range of 50 MeV–50 TeV. Three beam sizes were studied for each energy, corresponding to typical values of the betatron function. Specifically for thin targets, comparisons between fluka simulations and analytical Bethe equation calculations were carried out, which showed that the damage potential of a few-millimeter-thick graphite target and submillimeter-thick copper foil can be well estimated directly by the Bethe equation. The paper provides a valuable reference for the quick evaluation of potential damage to accelerator elements over a large range of beam parameters when beam loss occurs.

Nanostructured and microstructured thin foils have been fabricated and used experimentally as targets to manipulate the spatial profile of proton bunches accelerated through the interaction with high intensity laser pulses ($6\times {10}^{19}\mathrm{W}/{\mathrm{cm}}^2$). Monolayers of polystyrene nanospheres were placed on the rear surfaces of thin plastic targets to improve the spatial homogeneity of the accelerated proton beams. Moreover, thin targets with grating structures of various configurations on their rear sides were used to modify the proton beam divergence. Experimental results are presented, discussed, and supported by 3D particle-in-cell numerical simulations.

Beam optics control is of critical importance for machine performance and protection. Nowadays, turn-by-turn (TbT) beam position monitor (BPM) data are increasingly exploited as they allow for fast and simultaneous measurement of various optics quantities. Nevertheless, so far the best documented uncertainty of measured $\beta$-functions is of about 10‰ rms. In this paper we compare the $\beta$-functions of the ESRF storage ring measured from two different TbT techniques—the N-BPM and the Amplitude methods—with the ones inferred from a measurement of the orbit response matrix (ORM). We show how to improve the precision of TbT techniques by refining the Fourier transform of TbT data with properly chosen excitation amplitude. The precision of the N-BPM method is further improved by refining the phase advance measurement. This represents a step forward compared to standard TbT measurements. First experimental results showing the precision of $\beta$-functions pushed down to 4‰ both in TbT and ORM techniques are reported and commented.

We revisit the description of inverse Compton scattering sources and the photon beams generated therein, emphasizing the behavior of their phase space density distributions and how they depend upon those of the two colliding beams of electrons and photons. The main objective is to provide practical formulas for bandwidth, spectral density, brilliance, which are valid in general for any value of the recoil factor, i.e. both in the Thomson regime of negligible electron recoil, and in the deep Compton recoil dominated region, which is of interest for gamma-gamma colliders and Compton sources for the production of multi-GeV photon beams. We adopt a description based on the center of mass reference system of the electron-photon collision, in order to underline the role of the electron recoil and how it controls the relativistic Doppler/boost effect in various regimes. Using the center of mass reference frame greatly simplifies the treatment, allowing us to derive simple formulas expressed in terms of rms momenta of the two colliding beams (emittance, energy spread, etc.) and the collimation angle in the laboratory system. Comparisons with Monte Carlo simulations of inverse Compton scattering in various scenarios are presented, showing very good agreement with the analytical formulas: in particular we find that the bandwidth dependence on the electron beam emittance, of paramount importance in Thomson regime, as it limits the amount of focusing imparted to the electron beam, becomes much less sensitive in deep Compton regime, allowing a stronger focusing of the electron beam to enhance luminosity without loss of mono-chromaticity. A similar effect occurs concerning the bandwidth dependence on the frequency spread of the incident photons: in deep recoil regime the bandwidth comes out to be much less dependent on the frequency spread. The set of formulas here derived are very helpful in designing inverse Compton sources in diverse regimes, giving a quite accurate first estimate in typical operational conditions for number of photons, bandwidth, spectral density and brilliance values—the typical figures of merit of such radiation sources.

Several state-of-the-art metrology measurement methods have been investigated and combined for a fiducialization of accelerator components in the micrometric regime. The PACMAN project at CERN applied stretched-wire measurement methods to Compact Linear Collider quadrupole and cavity beam position monitor prototypes, to locate their magnetic, respectively, electromagnetic, axis using a dedicated test stand and to determine the position of the wire with respect to external alignment targets (fiducials) testing different methods, such as coordinate measuring machine measurements and microtriangulation. Further studies have been performed using a nanopositioning system, verifying the absolute accuracy and repeatability of the fiducialization method within a few micrometers.

The microbunching instability driven by beam collective effects in a linear accelerator of a free-electron laser (FEL) facility significantly degrades the electron beam quality and FEL performance. A conventional method to suppress this instability is to introduce an additional uncorrelated energy spread by laser-electron interaction, which has been successfully operated in the Linac Coherent Light Source and Fermi@Elettra, etc. Some other ideas are recently proposed to suppress the instability without increasing energy spread, which could benefit the seeded FEL schemes. In this paper, we propose a reversible electron beam heater using two transverse gradient undulators to suppress the microbunching instability. This scheme introduces both an energy spread increase and a transverse-to-longitudinal phase space coupling, which suppress the microbunching instabilities driven by both longitudinal space charge and coherent synchrotron radiation before and within the system. Finally the induced energy spread increase and emittance growth are reversed. Theoretical analysis and numerical simulations are presented to verify the feasibility of the scheme and indicate the capability to improve the seeded FEL radiation performance.

We have developed permanent magnet based dipole magnets for the next generation light sources. Permanent magnets are advantageous over electromagnets in that they consume less power, are physically more compact, and there is a less risk of power supply failure. However, experience with electromagnets and permanent magnets in the field of accelerators shows that there are still challenges to replacing main magnets of accelerators for light sources with permanent magnets. These include the adjustability of the magnetic field, the temperature dependence of permanent magnets, and the issue of demagnetization. In this paper, we present a design for magnets for future light sources, supported by experimental and numerical results.

Effects of the chromaticity on head-tail instabilities for broadband impedances are comprehensively studied, using the two particle model, the Vlasov analysis and computer simulations. We show both in the two particle model and the Vlasov analysis with the trapezoidal (semiconstant) wake model that we can derive universal contour plots for the growth factor as a function of the two dimensionless parameters: the wakefield strength, $\mathrm{\Upsilon }$, and the difference of the betatron phase advances between the head and the tail, $\chi$. They reveal how the chromaticity affects strong head-tail instabilities and excites head-tail instabilities. We also apply the LEP (Large Electron-Positron Collider) broadband resonator model to the Vlasov approach and find that the results are in very good agreement with those of the trapezoidal wake model. The theoretical findings are also reinforced by the simulation results. The trapezoidal wake model turns out to be a very useful tool since it significantly simplifies the time domain analysis and provides well-behaved impedance at the same time.

The thermally assisted photoemission (TAPE) effect was investigated for the hexaboride thermionic cathodes (${\mathrm{LaB}}_6$ and ${\mathrm{CeB}}_6$). It was found that the quantum efficiency of these cathodes can be increased by raising the cathode temperature along with the thermionic emission. In addition both materials can emit a measurable photoemission current by being irradiated with a laser having a photon energy below the work function at sufficiently high cathode temperatures. Our measurements indicate that this process is linear. These results show the significance of the TAPE effect. An additional effect of cathode heating is surface cleaning. This effect was detected as the hysteresis of the quantum efficiency which can be observed by heating up and cooling down the cathode. This effect slightly changes the quantum efficiency but not as much as the TAPE effect.

An undulator is a critical component to produce synchrotron radiation and a free electron laser. When a Bessel light beam carrying the orbit angular momentum copropagates with an electron beam bunch, a net transverse deflection force will be subjected to the latter one. As a result of dephasing effect, the deflection force will oscillate and act as an undulator. For such a laser based undulator, the period length can reach submillimeter level, which will greatly reduce the electron energy for the required x-ray production.

The emissions of the prebunched electron beam, including the coherent spontaneous emission and the self-amplified stimulated emission, are analyzed by using one-dimensional FEL theory. Neglecting the interaction of the electrons and the radiation field, the formula of the coherent spontaneous emission is given, the power of which is proportional to the square of the initial bunching factor and of the undulator length. For the general emission case of the prebunched electron beam, the evolution equation of the optical field is deducted. Then the analytical expression of the emission power is obtained for the resonant case; it is applicable to the regions from the low gain to the high gain. It is found that when the undulator length is shorter than four gain lengths, the emission is just the coherent spontaneous emission, and conversely, it is the self-amplified stimulated emission growing exponentially. For the nonresonant prebunched electron beam, the variations of the emission intensity with the detuning parameter for different interaction length are presented. The radiation field characters of the prebunched electron beam are discussed and compared with that of the seeded FEL amplifier.

In search of a low-Z pion production target for the Long Baseline Neutrino Facility (LBNF) of the Deep Underground Neutrino Experiment (DUNE) four graphite grades were irradiated with protons in the energy range of 140–180 MeV, to peak fluence of $\sim 6.1\times {10}^{20}\mathrm{p}/{\mathrm{cm}}^2$ and irradiation temperatures between $120–200°\mathrm{C}$. The test array included POCO ZXF-5Q, Toyo-Tanso IG 430, Carbone-Lorraine 2020 and SGL R7650 grades of graphite. Irradiation was performed at the Brookhaven Linear Isotope Producer. Postirradiation analyses were performed with the objective of (a) comparing their response under the postulated irradiation conditions to guide a graphite grade selection for use as a pion target and (b) understanding changes in physical and mechanical properties as well as microstructure that occurred as a result of the achieved fluence and in particular at this low-temperature regime where pion graphite targets are expected to operate. A further goal of the postirradiation evaluation was to establish a proton-neutron correlation damage on graphite that will allow for the use of a wealth of available neutron-based damage data in proton-based studies and applications. Macroscopic postirradiation analyses as well as energy dispersive x-ray diffraction of 200 KeV x rays at the NSLS synchrotron of Brookhaven National Laboratory were employed. The macroscopic analyses revealed differences in the physical and strength properties of the four grades with behavior however under proton irradiation that qualitatively agrees with that reported for graphite under neutrons for the same low temperature regime and in particular the increase of thermal expansion, strength and Young’s modulus. The proton fluence level of $\sim {10}^{20}{\mathrm{cm}}^{-2}$ where strength reaches a maximum before it begins to decrease at higher fluences has been identified and it agrees with neutron-induced changes. X-ray diffraction analyses of the proton irradiated graphite revealed for the first time the similarity in microstructural graphite behavior to that under neutron irradiation and the agreement between the fluence threshold of $\sim 5\times {10}^{20}{\mathrm{cm}}^{-2}$ where the graphite lattice undergoes a dramatic change. The confirmed similarity in behavior and agreement in threshold fluences for proton and neutron irradiation effects on graphite reported for the first time in this study will enable the safe utilization of the wealth of neutron irradiation data on graphite that extends to much higher fluences and different temperature regimes by the proton accelerator community searching for multi-MW graphite targets.

Microparticles (MP) and thermofield emission in vacuum are mainly caused by the roughness present at the surface of electrodes holding a high voltage. They can act as a trigger for breakdown, especially under high vacuum. This theoretical study discusses the interactions between one MP and the thermofield emission electron current as well as the consequences on the MP’s transit. Starting from Cranberg’s assumptions, new phenomena have been taken into account such as MP charge variation due to the secondary electron emission induced by energetic electron bombardment. Hence, the present model can be solved only numerically. Four scenarios have been identified based on the results, depending on the electron emission current from the cathode roughness (tip) and the size of the MP released at the anode, namely (i) one way; (ii) back and forth; (iii) oscillation; and (iv) vaporization. A crash study of the MP on the cathode shows that the electron emission can decrease if the MP covers the thermoemissive tip, i.e., if the MP is larger than the tip size—a phenomenon often called “conditioning”—and helping to increase the voltage holding in vacuum without breakdown.